Main Page
|
Course Admin
|
Contest Rules
|
Project Resources
|
Team Info
|
Picture Gallery
|
Contact Info
 
  You are here: RoboTag Main Page > Project Resources > Technical > Datasheets


Datasheets

The following datasheets are stored locally, with a link to where they were found on the web. If the datasheet detailed below seems out of date, check for a new version!

MIT HandyBoard - The unified hard-copy Handy Board technical document. Includes: explanation of Handy Board ports and connectors, quick start instructions, 6811 downloader explanation, freeware Interactive C manual, motor and sensor wiring diagrams, full schematics, printed circuit board artwork (1.5x scale), vendor and licensing information.

datasheet, webpage

Texas Instruments SN754410 Half H-Bridge - Quadruple Half-H Driver: provides bidirectional drive currents up to 1A at voltages from 4.5V to 36V. The device is designed to drive inductive loads such as relays, solenoids, dc and bipolar stepping motors, as well as other high-current/high-voltage loads in positive-supply applications.

datasheet, webpage

SGS Thompson L293D Half H-Bridge - a monolithic integrated high voltage, high current four channel driver designed to accept standard DTL or TTL logic levels and drive inductive loads (such as relays solenoides, DC and stepping motors) and switching power transistors. (600mA max)

datasheet, webpage

SGS Thompson L298 Full H-Bridge - an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. (4A max)

datasheet, webpage

Microchip PIC16F84A Microprocessor - FLASH/EEPROM microcontroller with an easy-to-learn instruction set (only 35 single word instructions). PIC16F84A contains 1024x14 word of FLASH program memory, 64 data memory bytes, and 68 bytes of user RAM. The device also features an 8-bit timer/counter with 8-bit programmable prescaler, Watchdog timer with its own on-chip RC oscillator for reliable operation, Power-On-Reset (POR) Power-up Timer (PWRT), Oscillator Start-up timer (OST) and a maximum speed of 20MHz.

datasheet, webpage

RALTRON 20MHz Crystal Oscillator - 14-pin DIP package (there are only 4 actual pins, but the device is 7-pins long) for use with the PIC as a high-speed clock source. 20.000MHz+-100ppm.

datasheet, webpage

ECS Ceramic Resonator (with caps) - this 3-pin package includes built-in load capacitors with the ceramic resonator. Used as a clock source for the PIC. 20MHZ+-0.5%.

datasheet, webpage

Panasonic PNA4601M IR Receiver - Bipolar integrated circuit with photodetect function. Used to demodulate an infrared signal (ie: identifies the carrier frequency and outputs the modulation frequency).

datasheet, webpage

LITEON LTM97AS-56 IR Receiver - Infrared remote control receiver module, a miniaturized receiver for infrared remote control systems. Includes a PIN diode and receiving preamplifier IC. Peak sensitivity: 940nm.

datasheet, appnote, webpage

LITEON LTE-302-M IR LED - high-intensity GaAs infrared emitting diode mounted in a clear plastic side-looking package. Peak IR: 940nm.

datasheet, webpage

Holtek HT12E Encoder - a CMOS LSI for remote control system applications. Capable of encoding information which consists of N address bits and 12-N data bits. Can be used for infrared, RF, or even on a fixed line with a shared bus.

datasheet, webpage

Holtek HT12D Decoder - a CMOS LSI for remote control system applications. Paired with Holtek 12E Encoders, these devices receive serial address and data from an RF or IR transmission medium.

datasheet, webpage

MING TX-01 Encoder Motherboard - The TX-01 is a encoder motherboard which is designed to be incorporated with the MING TX-99 transmission boards in order to provide a complete encoder/transmitter solution.

datasheet, webpage

MING TX-99-V3 RF Transmitter - The TX-99 v3.0 is a 300 MHz transmitter board which is designed to be incorporated with our TX-01 mothterboards in order to provide a complete encoder/transmitter solution.

datasheet, webpage

MING RE-01 Decoder Motherboard - decoder motherboard which is designed to be incorporated with the MING RE-99 receiver boards in order to provide a complete receiver/decoder solution.

datasheet, webpage

MING RE-99-V3 RF Receiver - The RE-99 v3.0A is a 300 MHz receiver board which is to be used with the MING RE-01 decoding motherboard if you will not be adding your own decoding microprocessor or chipset. The combination of both RE-99 v3.0A and the RE-01 will provide a complete receiver/decoder solution.

datasheet, webpage


 
Main Page
|
Course Admin
|
Contest Rules
|
Project Resources
|
Team Info
|
Picture Gallery
|
Contact Info